The Vortex shedding flow meter is somewhat different from other flow meters as it uses the principle known as the Von Karman effect. The principle states that when the flow of liquids and gasses passes through a bluff body, a pattern of swirling vortices is created simultaneously. It is repeated as a continuous activity when the pipeline flows through as the shed vortices are carried downstream in the flow. These are then detected by vortex shedding and fluidic flowmeters, and the same is measured. The vortex shedding flowmeters measure liquids and water’s velocity of varied types and are extensively used in modern industries.
Industries that use ordinary water, boiler feedwater, hydrocarbons, cryogenic liquids, chemicals, air, industrial gases, steam, and nitrogen measure the flow with the help of this Flow Meter. However, the flow meters must be top quality; otherwise, they will not give the right measurement. You would need to browse for a good supply source from a reliable dealer who has years of experience in this area and has been supplying all kinds of flow meters in the international market.
You may browse here at www.silverinstruments.com to get more information and the right type of flow meter for your industrial purposes by contacting their highly skilled engineers.
Table of Contents
Low Maintenance and Easy to Install Flow Meter
It is pretty easy to install a vortex flowmeter if you ask your technicians to do so in your factory. There are no moving parts which is one of the big advantages of this flow meter. It means you have to spend less time to maintain and repair. There is less leak occurring with this flow meter, and it also has a wide flow turndown range.
The vortex flowmeters use less energy when compared to other kinds of flow meters. It would mean that you can save on your power bills. When you need to calibrate it after using it for some time, your technicians will be able to do it with ease. They need to set the frequency generator at the upper range value and then adjust the fine-span screw to achieve 100% value. Your technical expert will disconnect the frequency generator, connect the signal lead, and modify it to zero. With this done, you will find the input and output matches accordingly.
The measurements are then taken with the help of a quality Paperless Recorder that can measure data over time. The Silver Instruments Co supplies some of the best paperless recorders in the international market.
Advantages of Ultrasonic Flow Meter
There are quite a few advantages if you install it at your factory. Your selection must be good at knowing its features. If not, you may hire an experienced and skilled technician. Firstly, you must know the flow measurement type and whether the same is volumetric or mass flow measurement. You should also see the kind of liquid that the meter will measure, like liquid, gas, or slurry, and any special conditions such as the viscosity of the flow and the particulates and also in Standby generators.
You must then install it with the help of a skilled technical expert as this type of flowmeter is pretty complex compared to other meters. When you have installed it, you will find that it does not block the path of liquid flow. The flow is bidirectional, and the meter’s response is always dynamic.
Again, you will find the meter fit and easy to maintain, and the versatility is good. It is noteworthy that the meter never contacts the liquid directly, and therefore there is no danger of leaks. Again, there are no moving parts or pressure loss. The biggest disadvantage is its price, and if you need one badly, you must be ready to budget for one. Even the meter’s accessories are costly and require a specialist to operate it and maintain it. However, it would help if you had a quality Paperless Recorder to record the measurement data over time.
Turbine Flow Meter and Oval Flow Meter
Several highly accurate meters give better results than simple and regular meters. The Turbine flow meter is worth mentioning for it is freely suspended and will rotate determined by the flow velocity. It is a very reliable meter and gives accurate measurement at all times. However, it does not work well with high viscous materials. For this, you may need an oval gear flow meter with two sides. No fluid passes through the center of the meter and is designed for use with high-viscous fluids and is especially used in oils, syrups, and fuel industries.
If you are ready to spend some money, then you can install the expensive Coriolis mass flowmeter specific to your purpose. It is the most accurate among all flow meters and is widely used in large manufacturing and processing industries. If you need such meters at a lower price than other sites, you can contact the above company for details, specifications, and shipping information.
Why Should You Purchase a Flow Meter?
The first question is the basic one that you need to answer before purchasing a flow meter. A flow meter is installed to measure the right amount of fluid, gas. Also steam, or liquid that passes through the pipes. The meter measures the linear, nonlinear, mass, or volumetric flow of the above elements. Any anomalies in the flow are calculated and recorded by the Paperless Recorder so that the management can make decisions accordingly.
The fluid flow through a pipe operates under a range of pressures and as per the temperatures inside it. Hence, there is a need for accurate measurement for both pressure and temperature. With the help of the data collected, an engineer can know the presence of abrasives, transmission qualities, and flow velocity. It also keeps the workforce safe as the anomalies in the flow are controlled or regulated.
Flow Meter and Usage
There are several types of flow meters, and each is used according to its function specific to industries. A mass flow meter, also known as an inertial flow meter. It is installed to measure the mass flow rate of fluid flowing through a pipe. On the other hand, a gas flow meter is a specialized flow meter used to measure the volume of fuel gases, including natural gas and liquefied petroleum gas.
There are other flow meters, and if you need more updated information, you may contact the above online site.